I have a little problem with my project at school,
the motor and servo arent operating as I hoped.

when i slide the slider all the way to the left it keeps on going to the left,
when i slide it to the right it goes to the left for 0.5sec en then slow to the right

the 2 motors arent responding at all...

i'm new to the arduino programming so that's why i am asking you guys to help me
*sorry for bad english im from holland (Netherlands)

Here is the code:

/*
   -- New project --
   
   This source code of graphical user interface 
   has been generated automatically by RemoteXY editor.
   To compile this code using RemoteXY library 2.2.5 or later version 
   download by link http://remotexy.com/en/library/
   To connect using RemoteXY mobile app by link http://remotexy.com/en/download/                   
     - for ANDROID 3.7.1 or later version;
     - for iOS 1.0.7 or later version;
     
   This source code is free software; you can redistribute it and/or
   modify it under the terms of the GNU Lesser General Public
   License as published by the Free Software Foundation; either
   version 2.1 of the License, or (at your option) any later version.     
*/

//////////////////////////////////////////////
//        RemoteXY include library          //
//////////////////////////////////////////////

// RemoteXY select connection mode and include library 
#define REMOTEXY_MODE__HARDSERIAL
#include <Servo.h>
Servo myservo;
Servo myservo_1;
#include <SoftwareSerial.h>
#include <RemoteXY.h>

// RemoteXY connection settings 
#define REMOTEXY_SERIAL Serial1
#define REMOTEXY_SERIAL_SPEED 9600

// RemoteXY configurate   
#pragma pack(push, 1)
uint8_t RemoteXY_CONF[] =
  { 5,0,58,0,6,7,0,2,0,12
  ,6,22,11,2,226,152,188,0,79,70
  ,70,0,1,1,54,16,12,12,2,226
  ,153,171,0,2,0,12,23,22,11,2
  ,226,150,178,0,226,150,188,0,4,176
  ,1,46,58,9,2,4,32,80,2,8
  ,57,2 };
   
// this structure defines all the variables of your control interface 
struct {

    // input variable
  uint8_t R; // =1 if switch ON and =0 if OFF
  uint8_t button_5; // =1 if button pressed, else =0
  uint8_t switch_1; // =1 if switch ON and =0 if OFF
  int8_t slider_1; // =-100..100 slider position
  int8_t slider_2; // =-100..100 slider position
  uint8_t PIN_DIR_1A;
  uint8_t PIN_DIR_1B;
  uint8_t PIN_DIR_2A;
  uint8_t PIN_DIR_2B;
  uint8_t PIN_SPD_1;
  uint8_t PIN_SPD_2;
 

    // other variable
  uint8_t connect_flag;  // =1 if wire connected, else =0

} RemoteXY;
#pragma pack(pop)

/////////////////////////////////////////////
//           END RemoteXY include          //
/////////////////////////////////////////////

#define PIN_R 13
#define PIN_BUTTON_5 10
#define PIN_SWITCH_1 A0
#define PIN_DIR_1A 7
#define PIN_DIR_1B 12
#define PIN_DIR_2A 11
#define PIN_DIR_2B 6
#define PIN_SPD_1 5
#define PIN_SPD_2 13

void setup() 
{
  RemoteXY_Init (); 
  myservo.attach(A1); 
  pinMode (PIN_R, OUTPUT);
  pinMode (PIN_BUTTON_5, OUTPUT);
  pinMode (PIN_SWITCH_1, OUTPUT);
  RemoteXY.slider_1 = 0;
   
  // TODO you setup code
   
}

void loop() 
{ 
  RemoteXY_Handler ();
   
  digitalWrite(PIN_R, (RemoteXY.R==0)?LOW:HIGH);
  digitalWrite(PIN_BUTTON_5, (RemoteXY.button_5==0)?LOW:HIGH);
  digitalWrite(PIN_SWITCH_1, (RemoteXY.switch_1==0)?LOW:HIGH);
   
   int pos = RemoteXY.slider_2;
  if (pos>0) { // up
    digitalWrite(7, HIGH);
    digitalWrite(12, LOW);
    digitalWrite(11, HIGH);
    digitalWrite(6, LOW);

    analogWrite(5, 255/100*RemoteXY.slider_2); 
    analogWrite(13, 255/100*RemoteXY.slider_2);
  } 
  else if (pos<0) { // down
   
    digitalWrite(PIN_DIR_1A, LOW);
    digitalWrite(PIN_DIR_1B, HIGH);
    digitalWrite(PIN_DIR_2A, LOW);
    digitalWrite(PIN_DIR_2B, HIGH);
    analogWrite(PIN_SPD_1, 255/100*pos);
    analogWrite(PIN_SPD_2, (0-pos) * 2.55);
   
  } 
  else { // stop
    digitalWrite(PIN_DIR_1A, LOW); 
    digitalWrite(PIN_DIR_1B, LOW);
    digitalWrite(PIN_DIR_2A, LOW);
    digitalWrite(PIN_DIR_2B, LOW);
   
    analogWrite(PIN_SPD_1, 0); 
    analogWrite(PIN_SPD_2, 0);
  } 
   
  {
   int pos = RemoteXY.slider_1;
  if (pos>0) { // Rechts
    analogWrite(A1, RemoteXY.slider_1 * 2.55);
   myservo.writeMicroseconds(RemoteXY.slider_1 * 20 + 500);
  } 
  else if (pos<-0) { // Links
    analogWrite(A1, RemoteXY.slider_1 * 2.55);
   myservo.writeMicroseconds(2500 - RemoteXY.slider_1 * 20); 
 
  } 

 
   
  // TODO you loop code
  // use the RemoteXY structure for data transfer
}
}

With kind regards,
Kellen