Success ran on Windows but on Linux found error both arduino ide 1.8.19 and 2.3.2

(Linux is Zorin Os 17)

THis is the code
//////////////////////////////////////////////
//        RemoteXY include library          //
//////////////////////////////////////////////

// you can enable debug logging to Serial at 115200
//#define REMOTEXY__DEBUGLOG   

// RemoteXY select connection mode and include library
#define REMOTEXY_MODE__ESP32CORE_BLUETOOTH
#include <BluetoothSerial.h>

// RemoteXY connection settings
#define REMOTEXY_BLUETOOTH_NAME "onebotic2"

#include <RemoteXY.h>

// RemoteXY configurate 
#pragma pack(push, 1)
uint8_t RemoteXY_CONF[] =   // 143 bytes
  { 255,4,0,7,0,136,0,17,0,0,0,31,1,106,200,1,1,9,0,130,
  255,255,108,203,0,8,5,25,129,56,56,0,19,25,31,71,15,20,77,77,
  56,0,19,19,125,0,0,0,0,0,0,200,66,0,0,160,65,0,0,32,
  65,0,0,0,64,19,0,2,9,89,32,16,0,19,26,8,8,79,78,0,
  79,70,70,0,129,16,110,17,6,19,76,73,71,72,84,0,129,60,110,31,
  6,19,67,85,84,32,83,80,69,69,68,0,4,54,91,47,11,128,19,0,
  129,3,5,55,9,19,79,78,69,66,79,84,73,67,45,50,0,65,93,4,
  9,9,112 };
 
// this structure defines all the variables and events of your control interface
struct {

    // input variables
  int8_t joy_main_x; // from -100 to 100}
  int8_t joy_main_y; // from -100 to 100}
  uint8_t btn_light; // =1 if switch ON and =0 if OFF
  int8_t sld_cutspeed; // =0..100 slider position

    // output variables
  float meter_speed; // from 0 to 100
  uint8_t led_red; // =0..255 LED Red brightness
  uint8_t led_green; // =0..255 LED Green brightness
  uint8_t led_blue; // =0..255 LED Green brightness

    // other variable
  uint8_t connect_flag;  // =1 if wire connected, else =0

} RemoteXY;
#pragma pack(pop)

/////////////////////////////////////////////
//           END RemoteXY include          //
/////////////////////////////////////////////

void setup()
{
  RemoteXY_Init ();
  Serial.begin(115200);
 
 
  // TODO you setup code
 
}

void loop()
{
  RemoteXY_Handler ();
  RemoteXY.meter_speed = sqrt(0.95*RemoteXY.joy_main_y*RemoteXY.joy_main_y+0.3*RemoteXY.joy_main_x*RemoteXY.joy_main_x);
  Serial.print(RemoteXY.joy_main_x);
  Serial.print(" ");
  Serial.print(RemoteXY.joy_main_y);
  Serial.print(" ");
  Serial.println(RemoteXY.meter_speed);
 
 
 
 
  // TODO you loop code
  // use the RemoteXY structure for data transfer
  // do not call delay(), use instead RemoteXY_delay()

}

Success ran on Windows but on Linux found error both arduino ide 1.8.19 and 2.3.2

(Linux is Zorin Os 17)

THis is the code
//////////////////////////////////////////////
//        RemoteXY include library          //
//////////////////////////////////////////////

// you can enable debug logging to Serial at 115200
//#define REMOTEXY__DEBUGLOG   

// RemoteXY select connection mode and include library
#define REMOTEXY_MODE__ESP32CORE_BLUETOOTH
#include <BluetoothSerial.h>

// RemoteXY connection settings
#define REMOTEXY_BLUETOOTH_NAME "onebotic2"

#include <RemoteXY.h>

// RemoteXY configurate 
#pragma pack(push, 1)
uint8_t RemoteXY_CONF[] =   // 143 bytes
  { 255,4,0,7,0,136,0,17,0,0,0,31,1,106,200,1,1,9,0,130,
  255,255,108,203,0,8,5,25,129,56,56,0,19,25,31,71,15,20,77,77,
  56,0,19,19,125,0,0,0,0,0,0,200,66,0,0,160,65,0,0,32,
  65,0,0,0,64,19,0,2,9,89,32,16,0,19,26,8,8,79,78,0,
  79,70,70,0,129,16,110,17,6,19,76,73,71,72,84,0,129,60,110,31,
  6,19,67,85,84,32,83,80,69,69,68,0,4,54,91,47,11,128,19,0,
  129,3,5,55,9,19,79,78,69,66,79,84,73,67,45,50,0,65,93,4,
  9,9,112 };
 
// this structure defines all the variables and events of your control interface
struct {

    // input variables
  int8_t joy_main_x; // from -100 to 100}
  int8_t joy_main_y; // from -100 to 100}
  uint8_t btn_light; // =1 if switch ON and =0 if OFF
  int8_t sld_cutspeed; // =0..100 slider position

    // output variables
  float meter_speed; // from 0 to 100
  uint8_t led_red; // =0..255 LED Red brightness
  uint8_t led_green; // =0..255 LED Green brightness
  uint8_t led_blue; // =0..255 LED Green brightness

    // other variable
  uint8_t connect_flag;  // =1 if wire connected, else =0

} RemoteXY;
#pragma pack(pop)

/////////////////////////////////////////////
//           END RemoteXY include          //
/////////////////////////////////////////////

void setup()
{
  RemoteXY_Init ();
  Serial.begin(115200);
 
 
  // TODO you setup code
 
}

void loop()
{
  RemoteXY_Handler ();
  RemoteXY.meter_speed = sqrt(0.95*RemoteXY.joy_main_y*RemoteXY.joy_main_y+0.3*RemoteXY.joy_main_x*RemoteXY.joy_main_x);
  Serial.print(RemoteXY.joy_main_x);
  Serial.print(" ");
  Serial.print(RemoteXY.joy_main_y);
  Serial.print(" ");
  Serial.println(RemoteXY.meter_speed);
 
 
 
 
  // TODO you loop code
  // use the RemoteXY structure for data transfer
  // do not call delay(), use instead RemoteXY_delay()

}