/*
   -- New project --
   
   This source code of graphical user interface 
   has been generated automatically by RemoteXY editor.
   To compile this code using RemoteXY library 2.4.3 or later version 
   download by link http://remotexy.com/en/library/
   To connect using RemoteXY mobile app by link http://remotexy.com/en/download/                   
     - for ANDROID 4.5.1 or later version;
     - for iOS 1.4.1 or later version;
    
   This source code is free software; you can redistribute it and/or
   modify it under the terms of the GNU Lesser General Public
   License as published by the Free Software Foundation; either
   version 2.1 of the License, or (at your option) any later version.    
*/

//////////////////////////////////////////////
//        RemoteXY include library          //
//////////////////////////////////////////////

// определение режима соединения и подключение библиотеки RemoteXY 
#define REMOTEXY_MODE__SOFTSERIAL
#include <SoftwareSerial.h>

#include <RemoteXY.h>

// настройки соединения 
#define REMOTEXY_SERIAL_RX 2
#define REMOTEXY_SERIAL_TX 4
#define REMOTEXY_SERIAL_SPEED 9600


// конфигурация интерфейса  
#pragma pack(push, 1)
uint8_t RemoteXY_CONF[] =
  { 255,1,0,0,0,11,0,10,13,1,
  4,32,25,6,13,86,2,26 };
  
// структура определяет все переменные и события вашего интерфейса управления 
struct {

    // input variables
  int8_t slider_1; // =-100..100 положение слайдера 

    // other variable
  uint8_t connect_flag;  // =1 if wire connected, else =0 

} RemoteXY;
#pragma pack(pop)

/////////////////////////////////////////////
//           END RemoteXY include          //
/////////////////////////////////////////////

int slider_1_s;

void setup() 
{
  RemoteXY_Init (); 
  Serial.begin(9600);
  
  RemoteXY.slider_1 = -100;
  // TODO you setup code
  
}

void loop() 
{ 
  RemoteXY_Handler ();
  slider_1_s = (RemoteXY.slider_1+100)*10+500;
// slider_tiller_s = map(slider_tiller_s, -100, 100, 0, 180);
  Serial.print(RemoteXY.slider_1);
  Serial.print(" | ");
  Serial.println(slider_1_s);
  
  // TODO you loop code
  // используйте структуру RemoteXY для передачи данных
  // не используйте функцию delay() 


}

-100 | 500
-100 | 500
-100 | 500
-100 | 500
-100 | 500
-88 | 620
-88 | 620
-88 | 620
-88 | 620
-88 | 620
-88 | 620
-88 | 620
-88 | 620
-88 | 620
-88 | 620
-88 | 620
-88 | 620
-88 | 620
-88 | 620
-88 | 620
-88 | 620
-88 | 620
-88 | 620
-23 | 1270
-23 | 1270
-23 | 1270
-23 | 1270
-23 | 1270
-23 | 1270
-23 | 1270
-23 | 1270
-23 | 1270
-23 | 1270
-23 | 1270
-23 | 1270
65 | 2150
65 | 2150
65 | 2150
65 | 2150
65 | 2150
65 | 2150
65 | 2150
65 | 2150
65 | 2150
65 | 2150
65 | 2150
65 | 2150
65 | 2150
65 | 2150
65 | 2150
65 | 2150
100 | 2500
100 | 2500
100 | 2500
100 | 2500
100 | 2500
100 | 2500
100 | 2500