Topic: ESP8266
Started researching RemoteXY and after reading some examples and having one failure while trying to test compile the code generated by RemoteXY. Now correct me if I am wrong but if you click the checkmark instead of the arrow pointing right in the Arduino IDE it should do a test compile and not attempt to upload the sketch.
Well, when I press the check icon it starts the test compile but fails due to a serial error. Now I have seen serial errors before but it is usually when the com port is not selected. But as I stated before if you are test compiling that should not matter, correct. Why then am I seeing this error?
C:\Users\me\Documents\Arduino\libraries\RemoteXY\src/modules/serial.h:42:12: error: 'serial' was not declared in this scope
return serial->available ();
^
exit status 1
Error compiling for board WeMos D1 R1.
Here is the code generated by RemoteXY
/*
-- New project --
This source code of graphical user interface
has been generated automatically by RemoteXY editor.
To compile this code using RemoteXY library 2.4.3 or later version
download by link http://remotexy.com/en/library/
To connect using RemoteXY mobile app by link http://remotexy.com/en/download/
- for ANDROID 4.5.1 or later version;
- for iOS 1.4.1 or later version;
This source code is free software; you can redistribute it and/or
modify it under the terms of the GNU Lesser General Public
License as published by the Free Software Foundation; either
version 2.1 of the License, or (at your option) any later version.
*/
//////////////////////////////////////////////
// RemoteXY include library //
//////////////////////////////////////////////
// RemoteXY select connection mode and include library
#define REMOTEXY_MODE__SOFTSERIAL
#include <SoftwareSerial.h>
#include <RemoteXY.h>
// RemoteXY connection settings
#define REMOTEXY_SERIAL_RX 2
#define REMOTEXY_SERIAL_TX 3
#define REMOTEXY_SERIAL_SPEED 115200
// RemoteXY configurate
#pragma pack(push, 1)
uint8_t RemoteXY_CONF[] =
{ 255,9,0,0,0,63,0,10,13,0,
2,0,37,11,22,11,2,26,31,31,
79,78,0,79,70,70,0,6,0,5,
4,20,20,2,26,5,0,66,2,30,
30,2,26,31,4,0,13,33,7,18,
2,26,1,0,44,38,12,12,2,31,
88,0,3,3,78,38,8,22,2,26 };
// this structure defines all the variables and events of your control interface
struct {
// input variables
uint8_t switch_1; // =1 if switch ON and =0 if OFF
uint8_t rgb_1_r; // =0..255 Red color value
uint8_t rgb_1_g; // =0..255 Green color value
uint8_t rgb_1_b; // =0..255 Blue color value
int8_t joystick_1_x; // =-100..100 x-coordinate joystick position
int8_t joystick_1_y; // =-100..100 y-coordinate joystick position
int8_t slider_1; // =0..100 slider position
uint8_t button_1; // =1 if button pressed, else =0
uint8_t select_1; // =0 if select position A, =1 if position B, =2 if position C, ...
// other variable
uint8_t connect_flag; // =1 if wire connected, else =0
} RemoteXY;
#pragma pack(pop)
/////////////////////////////////////////////
// END RemoteXY include //
/////////////////////////////////////////////
void setup()
{
RemoteXY_Init ();
// TODO you setup code
}
void loop()
{
RemoteXY_Handler ();
// TODO you loop code
// use the RemoteXY structure for data transfer
// do not call delay()
}