/*
-- New project --
This source code of graphical user interface
has been generated automatically by RemoteXY editor.
To compile this code using RemoteXY library 2.4.3 or later version
download by link http://remotexy.com/en/library/
To connect using RemoteXY mobile app by link http://remotexy.com/en/download/
- for ANDROID 4.3.1 or later version;
- for iOS 1.3.5 or later version;
This source code is free software; you can redistribute it and/or
modify it under the terms of the GNU Lesser General Public
License as published by the Free Software Foundation; either
version 2.1 of the License, or (at your option) any later version.
*/
//////////////////////////////////////////////
// RemoteXY include library //
//////////////////////////////////////////////
// RemoteXY select connection mode and include library
#define REMOTEXY_MODE__ESP8266_SOFTSERIAL_CLOUD
#include <SoftwareSerial.h>
#include <RemoteXY.h>
// RemoteXY connection settings
#define REMOTEXY_SERIAL_RX 2
#define REMOTEXY_SERIAL_TX 3
#define REMOTEXY_SERIAL_SPEED 9600
#define REMOTEXY_WIFI_SSID "xxxxxxxx"
#define REMOTEXY_WIFI_PASSWORD "xxxxxxx"
#define REMOTEXY_CLOUD_SERVER "cloud.remotexy.com"
#define REMOTEXY_CLOUD_PORT 6376
#define REMOTEXY_CLOUD_TOKEN "022cff562d1104e19650b5168541d64c"
// RemoteXY configurate
#pragma pack(push, 1)
uint8_t RemoteXY_CONF[] =
{ 255,4,0,0,0,71,0,8,13,0,
2,0,2,24,22,11,2,26,31,31,
79,78,0,79,70,70,0,2,0,27,
24,22,11,2,26,31,31,79,78,0,
79,70,70,0,2,0,52,24,22,11,
2,26,31,31,79,78,0,79,70,70,
0,2,0,77,24,22,11,2,26,31,
31,79,78,0,79,70,70,0 };
// this structure defines all the variables of your control interface
struct {
// input variable
uint8_t switch_1; // =1 if switch ON and =0 if OFF
uint8_t switch_2; // =1 if switch ON and =0 if OFF
uint8_t switch_3; // =1 if switch ON and =0 if OFF
uint8_t switch_4; // =1 if switch ON and =0 if OFF
// other variable
uint8_t connect_flag; // =1 if wire connected, else =0
} RemoteXY;
#pragma pack(pop)
/////////////////////////////////////////////
// END RemoteXY include //
/////////////////////////////////////////////
#define PIN_SWITCH_1 4
#define PIN_SWITCH_2 5
#define PIN_SWITCH_3 6
#define PIN_SWITCH_4 7
void setup()
{
RemoteXY_Init ();
pinMode (PIN_SWITCH_1, OUTPUT);
pinMode (PIN_SWITCH_2, OUTPUT);
pinMode (PIN_SWITCH_3, OUTPUT);
pinMode (PIN_SWITCH_4, OUTPUT);
// TODO you setup code
}
void loop()
{
RemoteXY_Handler ();
digitalWrite(PIN_SWITCH_1, (RemoteXY.switch_1==0)?LOW:HIGH);
digitalWrite(PIN_SWITCH_2, (RemoteXY.switch_2==0)?LOW:HIGH);
digitalWrite(PIN_SWITCH_3, (RemoteXY.switch_3==0)?LOW:HIGH);
digitalWrite(PIN_SWITCH_4, (RemoteXY.switch_4==0)?LOW:HIGH);
// TODO you loop code
// use the RemoteXY structure for data transfer
}