You are not logged in. Please login or register.
RemoteXY community → Boards → Arduino Nano BLE Sense
The Arduino Nano BLE Sense has BLE and many onboard sensors, it would be great to experiment with but I cannot get it to work with RemoteXY. The Arduino Uno R4 WiFi work fine. Do you have plans to include the Arduino Nano BLE Sense and the Arduino NanoESP32 boards?
You can try uploading the sketch you made for Arduino Uno R4. Since these boards use the same library for BLE it should work.
Topic - Error - Device not reply
Hi there, - I have the Nano Board 33 BLE Sens working well -
struct {
// output variables
float onlineGraph_01_var1;
float onlineGraph_01_var2;
float value_01;
float value_02;
float value_03;
uint8_t led_01_r; // =0..255 LED Red brightness
uint8_t led_01_g; // =0..255 LED Green brightness
uint8_t led_01_b; // =0..255 LED Green brightness
// other variable
uint8_t connect_flag; // =1 if wire connected, else =0
However, as soon as I enter one Label there will be no connection with BLE - Error - Device not reply ?? When I remove the Label - everything is fine again?
Make sure that when you copy the code from the editor after changing it, you need to copy the RemoteXY_CONF array and RemoteXY structure at the same time.
Check how the connection works without any additional code of yours, only the code from the editor.
If the code from the editor does not work, publish it here so we can check.
I have always copied everything at the same tine. So with identical rest of the code -
This one does work and connects!
//////////////////////////////////////////////
// RemoteXY include library //
//////////////////////////////////////////////
// you can enable debug logging to Serial at 115200
//#define REMOTEXY__DEBUGLOG
// RemoteXY select connection mode and include library
#define REMOTEXY_MODE__ARDUINOBLE
#include <ArduinoBLE.h>
// RemoteXY connection settings
#define REMOTEXY_BLUETOOTH_NAME "BS_Nano_33_BLE_Sens"
#include <RemoteXY.h>
// RemoteXY GUI configuration
#pragma pack(push, 1)
uint8_t RemoteXY_CONF[] = // 135 bytes
{ 255,0,0,23,0,128,0,19,0,0,0,66,83,32,78,97,110,111,32,51,
51,32,66,76,69,32,83,101,110,115,0,31,1,200,106,1,1,6,0,68,
10,19,119,53,50,8,36,135,82,111,108,108,32,91,194,176,93,0,80,105,
116,99,104,32,91,194,176,93,0,67,146,20,40,10,78,2,26,2,67,146,
41,40,10,78,2,26,3,67,146,62,40,10,78,2,26,2,65,147,83,13,
13,112,129,41,2,126,8,64,1,83,101,110,115,111,114,101,110,32,78,97,
110,111,32,51,51,32,66,76,69,32,83,101,110,115,0 };
// this structure defines all the variables and events of your control interface
struct {
// output variables
float onlineGraph_01_var1;
float onlineGraph_01_var2;
float value_01;
float value_02;
float value_03;
uint8_t led_01_r; // =0..255 LED Red brightness
uint8_t led_01_g; // =0..255 LED Green brightness
uint8_t led_01_b; // =0..255 LED Green brightness
// other variable
uint8_t connect_flag; // =1 if wire connected, else =0
} RemoteXY;
#pragma pack(pop)
/////////////////////////////////////////////
// END RemoteXY include //
/////////////////////////////////////////////
This one – with just one additional Label – does not connect!
//////////////////////////////////////////////
// RemoteXY include library //
//////////////////////////////////////////////
// you can enable debug logging to Serial at 115200
//#define REMOTEXY__DEBUGLOG
// RemoteXY select connection mode and include library
#define REMOTEXY_MODE__ARDUINOBLE
#include <ArduinoBLE.h>
// RemoteXY connection settings
#define REMOTEXY_BLUETOOTH_NAME "BS_Nano_33_BLE_Sens"
#include <RemoteXY.h>
// RemoteXY GUI configuration
#pragma pack(push, 1)
uint8_t RemoteXY_CONF[] = // 148 bytes
{ 255,0,0,23,0,141,0,19,0,0,0,66,83,32,78,97,110,111,32,51,
51,32,66,76,69,32,83,101,110,115,0,31,1,200,106,1,1,7,0,68,
10,19,119,53,50,8,36,135,82,111,108,108,32,91,194,176,93,0,80,105,
116,99,104,32,91,194,176,93,0,67,146,20,40,10,78,2,26,2,67,146,
41,40,10,78,2,26,3,67,146,62,40,10,78,2,26,2,65,147,83,13,
13,112,129,41,2,126,8,64,1,83,101,110,115,111,114,101,110,32,78,97,
110,111,32,51,51,32,66,76,69,32,83,101,110,115,0,129,60,84,36,12,
64,17,76,97,98,101,108,0 };
// this structure defines all the variables and events of your control interface
struct {
// output variables
float onlineGraph_01_var1;
float onlineGraph_01_var2;
float value_01;
float value_02;
float value_03;
uint8_t led_01_r; // =0..255 LED Red brightness
uint8_t led_01_g; // =0..255 LED Green brightness
uint8_t led_01_b; // =0..255 LED Green brightness
// other variable
uint8_t connect_flag; // =1 if wire connected, else =0
} RemoteXY;
#pragma pack(pop)
/////////////////////////////////////////////
// END RemoteXY include //
/////////////////////////////////////////////
Hi there -
Boards: Arduino Nano 33 BLE or Nano 33 BLE SENS
I have payed a little bit more with the instability in connectivity. I have no started to ONLY do the GUI first, compile and Upload as it is and have discovered, that no changes
- BUT e.g. adding on more graph to.the online graph will kill the the connectivity (no connection between phone and board)
- OR one slight change of size to.the online graph
- OR adding / changing a legend
- OR one more edit fields etc.
will kill the the connectivity. To exactly finding the "edge" I have disposed several GUI setups as it sometimes is faster to build from scratch than to work back!
All in all it's not really convenient to actually work with although I do like the overall setup very much!
Hope that helps to fix this strange behavior.
Kind regards
We tested your example on other boards and it works. Most likely the problem is related to the Nano 33 BLE board. Now we are waiting for this board for tests
Hi there,
Are there any results yet? Since my post I have verified the bug several times and this week I actually also reproduced it on a Nano 33 BLE board.
So I would be very interested to hear your experience!
Kind regards, and thanks a lot
Yes, we have reproduced the bug. The bug is confirmed.
Thx a lot for confirmation! Any idea when there will be a fix? It would be great to know when it makes sense to extend the GUIs again.
Kind regards and thx a lot
Thx a lot for confirmation! Any idea when there will be a fix? It would be great to know when it makes sense to extend the GUIs again.
Kind regards and thx a lot
We will try to do it as soon as possible. Since the ArduinoBLE library is used with different controllers, we must also test them.
As a temporary solution, you can replace the RemoteXYStream_ArduinoBLE.h file in the library with a file from the github repository https://github.com/RemoteXY/RemoteXY-Ar … duinoBLE.h
Hi there -
thanks for that!
Replaced the RemoteXYStream_ArduinoBLE.h - changed the old version to *.bak and after compilation with Arduino IDE I do get:
"In file included from C:\Users\b.stenkamp\Documents\Arduino\libraries\RemoteXY\src/RemoteXY.h:160:0,
from C:\Users\b.stenkamp\AppData\Local\Temp\.arduinoIDE-unsaved2025615-16452-ww2aym.7j0lr\sketch_jul15a\sketch_jul15a.ino:34:
C:\Users\b.stenkamp\Documents\Arduino\libraries\RemoteXY\src/RemoteXYStream_ArduinoBLE.h:153:8: error: 'void CRemoteXYStream_ArduinoBLE::flush()' marked 'override', but does not override
void flush () override {
^~~~~
exit status 1
Compilation error: exit status 1"
Any quick ideas?
Thx so much!!
You may be trying to replace a file in one of the previous versions of the library. You need to install version 4.1.1 and replace its file. https://remotexy.com/en/library/
You can download the entire library together with the file before the release. https://github.com/RemoteXY/RemoteXY-Ar … master.zip
Hi there,
full replacement of the library has done the job - compilation successful and original issue with the library seems to be fixed as well!
Thx so much!! - waiting for the next library update to have it on all machines here - but hot fix for now is great!
Hi there
Just a quick update - the below code directly from the editor unfortunately
- does not show the letters in the indicator fields
- is not stable in connection ti the board - disconnects and reconnects with intervals of about 10-15 seconds
Hope that further helps to get the library up and running!
kind regards and thx so much for your support.
https://remotexy.com/en/editor/278ae19d … e9a2fae4c/
/*
-- 2025_KS1_DataCom --
To compile this code using RemoteXY library 3.1.13 or later version
download by link [url]http://remotexy.com/en/library/[/url]
To connect using RemoteXY mobile app by link [url]http://remotexy.com/en/download/[/url]
- for ANDROID 4.15.01 or later version;
- for iOS 1.12.1 or later version;
To interact with the GUI, please refer to the manual:
[url]https://remotexy.com/ru/help/code/interaction/[/url]
This source code was automatically generated by the RemoteXY editor and
is an example for the RemoteXY library.
Licensed under the MIT License. See the LICENSE file in the RemoteXY library
root ([url]https://github.com/RemoteXY/RemoteXY-Arduino-library[/url]) for full license
details.
*/
//////////////////////////////////////////////
// RemoteXY include library //
//////////////////////////////////////////////
// you can enable debug logging to Serial at 115200
//#define REMOTEXY__DEBUGLOG
// RemoteXY select connection mode and include library
#define REMOTEXY_MODE__ARDUINOBLE
#include <ArduinoBLE.h>
// RemoteXY connection settings
#define REMOTEXY_BLUETOOTH_NAME "2025_KS1"
#include <RemoteXY.h>
// RemoteXY GUI configuration
#pragma pack(push, 1)
uint8_t RemoteXY_CONF[] = // 315 bytes
{ 255,18,0,25,0,52,1,19,0,0,0,50,48,50,53,95,75,83,49,0,
30,2,106,200,200,128,1,1,14,0,2,7,22,23,34,72,5,47,15,0,
36,123,16,32,83,101,110,100,101,110,0,69,109,112,102,97,110,103,101,110,
0,74,5,40,21,16,9,25,53,12,5,2,123,24,64,69,109,112,102,97,
110,103,101,110,0,74,74,42,21,16,145,27,40,10,13,31,1,31,64,83,
101,110,100,101,110,0,74,75,62,21,16,70,39,57,6,13,2,31,8,64,
69,109,112,102,97,101,110,103,101,114,32,65,100,114,101,115,115,101,0,7,
74,114,21,16,126,81,59,8,100,64,31,1,2,11,67,6,119,21,16,10,
80,59,8,100,24,123,17,74,39,123,21,16,77,74,40,6,13,2,31,8,
64,77,101,115,115,97,103,101,32,60,32,49,54,0,74,39,87,21,16,76,
52,45,6,13,2,31,8,64,66,105,116,98,114,101,105,116,101,32,105,110,
32,109,115,32,62,32,49,0,7,40,94,21,16,78,61,39,8,118,64,2,
26,2,74,41,142,21,16,77,91,40,6,13,2,31,8,64,80,97,114,105,
116,121,0,67,6,158,21,16,11,101,9,10,92,2,26,67,66,153,21,16,
176,100,8,9,94,2,26,7,6,67,21,16,10,43,22,10,118,64,24,123,
2,7,74,65,16,16,163,43,22,10,118,64,31,1,2 };
// this structure defines all the variables and events of your control interface
struct {
// input variables
uint8_t Com_Type; // =1 if switch ON and =0 if OFF
char Send_Message[11]; // string UTF8 end zero
int16_t edit_01; // -32768 .. +32767
int16_t Rec_Adress; // -32768 .. +32767
int16_t Send_Adress; // -32768 .. +32767
// output variables
uint8_t strings_01; // from 0 to 1
uint8_t strings_02; // from 0 to 1
uint8_t Receiver_Adress; // from 0 to 1
char Receive_Message[17]; // string UTF8 end zero
uint8_t strings_03; // from 0 to 1
uint8_t strings_04; // from 0 to 1
uint8_t strings_05; // from 0 to 1
int8_t Parity_Receiver; // -128 .. 127
int8_t Rarity_Sender; // -128 .. 127
// other variable
uint8_t connect_flag; // =1 if wire connected, else =0
} RemoteXY;
#pragma pack(pop)
/////////////////////////////////////////////
// END RemoteXY include //
/////////////////////////////////////////////
void setup()
{
RemoteXY_Init ();
// TODO you setup code
}
void loop()
{
RemoteXY_Handler ();
// TODO you loop code
// use the RemoteXY structure for data transfer
// do not call delay(), use instead RemoteXY_delay()
}RemoteXY community → Boards → Arduino Nano BLE Sense
Powered by PunBB, supported by Informer Technologies, Inc.